Weld Mount

Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength in 15 -20 minutes. This makes...

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop...

Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures in 10 - 12 minutes and has working strength within 40 minutes. AT-4020 is recommended for composite and plastic bonding applications and...

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop...

Adhesive Dispensing GunThe AT-300 Adhesive dispensing gun has a 1:1 plunger for use with AT-2010 and AT-4020 50ml cartridges (sold separately) When using AT-6030 adhesive it requires AT-12 (10 to 1 plunger). Replacement plungers are also available.

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop...

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop...

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44"...

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44"...

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44"...

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44"...

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for...

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for...

.75" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other...

1" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other...

1.25" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other...

1.5" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other...

1" Tall Stainless Stud w/1/4" x 20 ThreadMounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4" x 20 threads. Use for hanging panels, through deck mounts and many other...

1.5" Tall Stainless Stud w/1/4" x 20 ThreadMounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4" x 20 threads. Use for hanging panels, through deck mounts and many other...

1.5" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from...