Weld Mount

AT-3B Small Black Nylon Wire Tie Mount - Qty. 500The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs....

Adhesively Bonded Fastener Kit with AT 8040 AdhesiveKit Contains: (1) Plano Storage Box - 11" x 7.25" x 2.75" (50) AT-5 Tie Mount (White) (1) AT-8040 Adhesive (5) AT-850 Mixing Tip (1) AT-300 Dispensing Gun (2) AT-113B Black Footmans Loop (4) ST125-1420-16 Stainless Stud Quick Guide (pdf)Owner's Manual (pdf)

Aluminum Base Wire Tie MountThis tie mount is provided with an anodized aluminum base with a nylon tie mount which is riveted to the base. The nylon mount swivels 360 degrees making alignment with the wire harness easier. This tie mount is designed for a #5 wire tie and has...

Stainless Steel Standoff 1.25" Base 1/4" x 20 Thread .75" Tall - 6-PackUnlike the SOB standoffs which have a blind thread, the SOT series standoffshave a thread which runs all the way through the barrel of the standoff.This allows the standoff to be mounted from either side of the base....

Acrylic Adhesive - 10-PackCAN NOT SHIP AIR,UPS GROUND ONLYAT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures in 10 - 12 minutes and has working strength within 40 minutes. AT-4020 is recommended for composite and plastic bonding...

{Standard Start-Up Kit - No AdhesiveThe 65109 Start Up Kit has a wide variety of Weld Mount parts designed to give the user the chance to try numerous applications at a low cost.Kit Contains: 1 pc AT-300 Adhesive Dispensing Gun 5 pc. AT-850 Adhesive Mixing Tips 50 pc. AT-5 White...

10:1 Gun Plunger for AT-6030 Adhesive10 Pack Gun Plunger for AT-6030 Adhesive (sold separately)

Stainless Steel Stud 1.25" Base 1/4 x 20 Threads 2.25" Tall - 10 PiecesThe stainless steel stud mounts to virtually any surface using our acrylic adhesive. This is a structural part with 500 lbs of tensile strength and 650 lbs in shear. All studs have 1/4 x 20 threads. Use...

Industrial Kit with AT-8040 AdhesiveThis Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For Industrial Maintenance Shops. A Wide Selection Of Weld Mount Parts Are Supplied In A Heavy "Durham" Metal Box Which Is A Standard Rack Mounted System. The Kit...

Stainless Steel Stud 1.25" Base 10 x 24 Threads .50" Tall - 15 QuantityStuds with smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items that require a smaller stud diameter. These studs can be bonded from either surface of the base...

Stainless Steel Stud 1.25" Base 10 x 24 Threads 1.00" Tall - 15 QuantityStuds with smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items that require a smaller stud diameter. These studs can be bonded from either surface of the base...

AT-6031 Metal Bond AdhesiveAT-6031 is a 10-to-1 metal bonding adhesive. It has high viscosity (cures in 10–12 minutes), has a 6-minute working time, and develops working strength in 40 minutes. AT-6031 develops more than 2,500 lbs. (psi) of tensile strength on most metal surfaces, making it an ideal alternative to...

AT-651 Mixing Tips for Use with AT-6031 Adhesive - Qty. 10Weld Mount’s AT-651 mixing tip is designed specifically for use with Weld Mount’s AT-6031 adhesive. AT-6031 is a 10 to 1 adhesive that requires a mixing tip with more mixing chambers to ensure proper mixing before use. These mixing tips...

8040 Acrylic Adhesive with Plunger AT-8040 is a good general-purpose adhesive packaged in a manual plunger cartridge. Simply snip off the two end caps dispense the needed amount of adhesive onto a clean surface and mix it by hand. AT-8040 cures in 10-12 minutes, has a 6-minute working time and develops...