NAVDoctor NMEA Network Diagnostic ToolNAVDoctor is the perfect NMEA 2000 diagnostic tool for dealers, installers, and boat builders. It turns any mobile device into an NMEA 2000 network analyzer, creating simple and clear web pages that show the health and status of your NMEA 2000 network. NAVDoctor is a portable NMEA...

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44"...

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for...

AT-3 Small White Nylon Tie Mount - Qty. 500The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The...

1.5" Tall Stainless Stud w/1/4" x 20 ThreadMounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4" x 20 threads. Use for hanging panels, through deck mounts and many other...

Aluminum Wire TieUsed with Stainless Steel or Nylon wire ties up to 0.4 inches wide. 250 lbs tensile strength when bonded with AT-6030 adhesive manufactured of 5052 marine grade aluminum for UV and salt water resistance. Ideal alternative to welding or drilling and tapping to mount hoses, conduit, etc.

1.5" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other...

AT-850 Square Mixing Tip 4" - Case of 50Weld Mount's AT-850 tip is for use only with the 2010, 4010, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.Features: Square Mixing Tip 4" Long Case of 50

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44"...

Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength in 15 -20 minutes. This makes...

AT-651 Mixing Tips for Use with AT-6031 Adhesive - Qty. 10Weld Mount’s AT-651 mixing tip is designed specifically for use with Weld Mount’s AT-6031 adhesive. AT-6031 is a 10 to 1 adhesive that requires a mixing tip with more mixing chambers to ensure proper mixing before use. These mixing tips...

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop...

8040 Acrylic Adhesive with Plunger AT-8040 is a good general-purpose adhesive packaged in a manual plunger cartridge. Simply snip off the two end caps dispense the needed amount of adhesive onto a clean surface and mix it by hand. AT-8040 cures in 10-12 minutes, has a 6-minute working time and develops...

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44"...

AT-6031 Metal Bond AdhesiveAT-6031 is a 10-to-1 metal bonding adhesive. It has high viscosity (cures in 10–12 minutes), has a 6-minute working time, and develops working strength in 40 minutes. AT-6031 develops more than 2,500 lbs. (psi) of tensile strength on most metal surfaces, making it an ideal alternative to...

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop...

Stainless Steel Stud 1.25" Base 10 x 24 Threads 1.00" Tall - 15 QuantityStuds with smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items that require a smaller stud diameter. These studs can be bonded from either surface of the base...

1.5" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from...

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for...

AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.Features: Square Mixing Tip 4" Long...