Tools

Adhesive Dispensing GunThe AT-300 Adhesive dispensing gun has a 1:1 plunger for use with AT-2010 and AT-4020 50ml cartridges. When using AT-6030 adhesive it requires AT-12 (10 to 1 plunger). Replacement plungers are also available.

Pro Dual Feed Motor Flusher with Rectangular CupsFeatures: Dual Feed Motor Flusher Rectangular Cups Included

Universal Motor Flusher with Round CupsFeatures: Universal Motor Flusher Round Cups Included

Plastic Suction Cup HandleInjection Molded Nylon/Nitrile-Buna Rubber Portable, dual suction cup handle installs instantly. Mounts in any direction on any non-porous surface. Easily mount and re-mount with no marks or damage to hull. No holes, screws, or tools required. Ideal for cleaning waterlines or boat bottoms while swimming or from a...

1" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other...

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop...

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for...

Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength in 15 -20 minutes. This makes...

AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.Features: Square Mixing Tip 4" Long...

Adhesive Mixing Tip For AT-6030Our AT-650 mixing tip is designed specifically for use with our AT-6030 adhesive. AT-6030 is a 10 to 1 adhesive which requires a mixing tip with more mixing chambers to insure proper mixing before use. These mixing tips minimize waste compared with traditional 6" mixing tips....

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44"...

Add-A-Snap - Black - 1-1/2" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer,...

Emergency Deck Fill PlugNitrile-Buna RubberThis Emergency Deck Fill Plug is a must for any vessel. Fits most 1-1/2" hose deck fills in the event you lose your cap. For temporary use only until you can replace your OEM cap. Constructed of fuel resistant Nitrile-Buna rubber. WARNING: This product can expose...

Add-A-Snap - White - 2-1/2" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth...

Add-A-Snap - Black - 4" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth...

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44"...

1.25" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from...

Aluminum Wire TieUsed with Stainless Steel or Nylon wire ties up to 0.4 inches wide. 250 lbs tensile strength when bonded with AT-6030 adhesive manufactured of 5052 marine grade aluminum for UV and salt water resistance. Ideal alternative to welding or drilling and tapping to mount hoses, conduit, etc.

AT-5B Large Black Nylon Wire Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved...

2.5" Tall Stainless Stud w/1/4" x 20 ThreadMounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4" x 20 threads. Use for hanging panels, through deck mounts and many other...